The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
We've unearthed this article involving How to Install a Bathtub listed below on the internet and figured it made good sense to relate it with you over here.
Installing a tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is readily obtainable, the task can move quickly; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also set in the new one. Make certain you have actually certified on your own for the job as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This article will certainly assist you install a brand-new bath tub in your washroom if you have actually already gotten a brand-new tub and do not need to alter the plan of your previous water pipes.
Your devices and material checklist must make up the following:
Planning for the Setup
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The procedure of removing the existing taps can be quite troublesome due to the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using the two wood boards under its feet, put the bathtub in the required placement. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and examine all joints and new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as additionally check the overflow outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub needs to wait until the bathtub has actually been utilized at the very least when as this will settle it into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washers are in location in between the tap as well as the sink. Safeguard the faucet in position with the producer provided backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous kind should be connected to the tap ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, triggering the water to permeate the wall surface between the bath and the tiling, bring about complications with wetness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and installations. They are sold in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can split fairly very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give a remark directly below. We'd be interested to know your thoughts about this blog posting. We are looking forward that you visit us again soon. Enjoyed our entry? Please share it. Let someone else check it out. We enjoy reading our article about How to Install a Bathtub.
Stress-free? Call now! Report this page